Wheel Apparatus has been involved with the ASTM Standardization Process for over 30 Optional Test Kits are available for either ASTM B or G testing. EPI Materials Testing group does custom wear testing and three standardized wear tests for their clients, ASTM G65, G, and B ASTM Methods ASTM G65 – 04 Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus ASTM G – 02() Standard.
|Published (Last):||23 December 2005|
|PDF File Size:||17.88 Mb|
|ePub File Size:||10.3 Mb|
|Price:||Free* [*Free Regsitration Required]|
It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Abradant properties, namely hardness and crushing strength 6. It is the responsibility of the user of this standard to establish appropriate safety g150 health practices and determine the applicability of regulatory limitations prior to use.
To provide analogue voltage friction force signal for data logger or chart recorder input. Materials of higher abrasion resistance will have a lower volume loss. There is therefore a need for a reliable and convenient approach to the study of abrasive wear properties.
The machine is floor standing with test assemblies mounted on a back-plate and abradant discharged downwards into a hopper. You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server.
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Since the test method does not attempt to duplicate all of the process conditions abrasive size, shape, pressure, impact or corrosive elementsit should not be used to predict the exact resistance of a given material in a specific environment.
TE 65 MULTIPLEX SAND/WHEEL ABRASION TESTER
Smaller quantities are desirable if non-standard abradants are to be used. This means that fully wet tests can be carried out, with the mass flow of abradant still controlled.
Add to Alert PDF. The comparison will provide a general indication of the worth of the unknown materials if abrasion is the predominant factor causing deterioration of the materials. It is the intent of this procedure to provide data that will reproducibly rank materials in their resistance to scratching abrasion under a specified set of conditions.
Including precision abradant feed system and peristaltic pump for alternative horizontal loading configuration. asttm
ASTM G – Standard Test Method for Conducting Wet Sand/Rubber Wheel Abrasion Tests
The values given in parentheses are for information only. Test Configurations ASTM G 65 uses hopper g150 sand through a defined nozzle and loads the test piece sideways on to the wheel. It would be preferable to be able to run with smaller samples or even to run multiple tests on one sample, thus reducing the cost per test. Need more than one copy? It is clear, therefore, that a single set of test conditions will not be sufficient for determining the wear resistance of diverse materials.
Particle speed or cutting speed 4.
ASTM G – 16 Standard Test Method for Conducting Wet Sand/Rubber Wheel Abrasion Tests
Particle loading, the nominal load carried by each particle of abradant 2. For wet tests, water is introduced on to the wheel surface, just behind the chute. With variable speed drive motor and manually controlled pneumatic loading with precision regulator, force transducer and digital display. Lower flow rates are desirable if non-standard abradants are to be used, thus requiring smaller batches to be produced.
In all cases the abrasive used is rounded quartz grain sand. Imbeni V Hutchings I. Please first verify your email before subscribing to alerts.
The abradant is fed from a hopper to a rotating drum with a shallow groove on its surface. Abradant particle shape or angularity It is clear, therefore, that a single set of test conditions will not be sufficient for determining the wear resistance of diverse materials.
Background Abrasive wear of industrial materials handling plant e. It is the intent of this procedure to provide data that will reproducibly rank materials in their resistance to scratching abrasion under a specified set of conditions.
This standard is also available to be included in Standards Subscriptions. You may delete a document from your Alert Profile at any time.
In this test method these conditions are standardized to develop a uniform condition of wear which has been referred to as scratching abrasion 1 and 2. The ASTM test pieces are relatively large and therefore expensive to prepare out of typical hard surfacing materials. Abrasive wear is also an important factor in determining the life of tillage and construction equipment and in the case of tillage tools has a direct impact on the draft forces required to pull the plough.
The wet rubber and steel wheel tests use a large volume of slurry containing 1.
Rubber Wheel Sand Abrasion machine tests
The wear resistance of a material cannot be predicted reliably from simple properties such as bulk hardness, elastic modulus or tensile strength. ASTM B uses a steel wheel, thus providing higher stress abrasion than the rubber wheel tests. The alternative abradant feed system is designed to give a range of constant feed rates and produce an even monolayer of particles on the wheel in front of the contact. Particle loading awtm be controlled over a wide range by adjusting the mass flow and the normal load on the test block.
Abrasive wear of industrial materials handling plant e. Subscription pricing is determined by: Excluding precision abradant feed system and peristaltic pump for alternative horizontal loading configuration.
Already Subscribed to this document. A number of standard methods have been developed with the aim of producing test data that will reproducibly rank materials under a specified set of conditions.
With variable speed drive motor, servo controlled pneumatic loading with force transducer feedback, astn force transducer, displacement transducer.
This is not possible in the ASTM configuration. Any abradant that does not pass through the contact may be collected separately and therefore the quantity of abradant actually passing the test block may be determined. Volume loss data obtained from test materials whose lives are unknown in a specific abrasive environment may, however, be compared wstm test data obtained from a material whose life is known in the same environment. In practice, abrasive materials will vary considerably h105 hardness, crushing strength and shape from the sand specified in the ASTM standards.
The TE 65 is designed to perform tests according to the conditions described in the following methods:. The consumption of sand is also high due to the large mass flow required. Your Alert Profile lists the documents that will be monitored. The TE 65 includes the option of a second loading position that presses the specimen on to the top of the wheel, with the specimen horizontal.